Simply the best automated camera system you can put in your race car for this price point. Pair this with your AIM Solo or dash and have fully automatic instant video with data overlay. No software editing, no charging batteries, no record button. Everything just happens for you! This paired with an AIM PDM+Dash Kit and you're fully set! AND Now in Full HD image 1920 x 1080 resolution, at 30 fps!
Running a K series engine harness but using your stock S2000 (00-05) throttle body? You will need to convert the TPS Connector to the older B series style. Or just use this quick and easy jumper/adapter. plug in and go.
Running the RSX Engine Harness/ECU? This is the chassis adapter to plug it into your S2000. Only works for 2000-2005 year S2000's. IF USING RYWIRE ECU HARNESS- you will use the other Rywire Specific Jumper Harness.
Looking to run multiple AIM CAN devices- You'll most likely need this. If using the AiM PDM's, you'll need this to run additional CAN devices beyond the AiM GPS.
Winning Formula DBW Anti-Vibration Kit for KPower Intake manifold to Bosch 70mm DBW Throttle Body. K24's are one of the worst engines for vibrations and harmonics, esp when exceeding 7500rpm's. Those vibrations get sent into the DBW and cause all sorts of issues. From mismatched TPS readings to the gears stripping. The boys at Winning Formula have developed and vigorously tested these and are proven to fix all the DBW issues. Kit includes: Intake and throttle body adapters Silicone coupler Hose clamps (QTY.2) Associated hardware with anti-vibration washers O-rings
Winning Formula DBW Anti-Vibration Kit for KPower Intake manifold to the stock FA20 DBW Throttle body. K24's are one of the worst engines for vibrations and harmonics, esp when exceeding 7500rpm's. Those vibrations get sent into the DBW and cause all sorts of issues. From mismatched TPS readings to the gears stripping. The boys at Winning Formula have developed and vigorously tested these and are proven to fix all the DBW issues. Kit includes: Intake and throttle body adapters Silicone coupler Hose clamps (QTY.2) Associated hardware with anti-vibration washers O-rings
Winning Formula DBW Anti-Vibration Kit for 00-05 S2000 intake to Bosch 70mm DBW Throttle Body. K24's are one of the worst engines for vibrations and harmonics, esp when exceeding 7500rpm's. Those vibrations get sent into the DBW and cause all sorts of issues. From mismatched TPS readings to the gears stripping. The boys at Winning Formula have developed and vigorously tested these and are proven to fix all the DBW issues. Kit includes: Intake and throttle body adapters Silicone coupler Hose clamps (QTY.2) Associated hardware with anti-vibration washers O-rings
The ideal CAN expansion accessory for all Elite Series ECUs. Includes: Single Channel, CAN Wideband Controller, 4.9LSU Sensor, CAN Cable (4'/1200mm), Power Supply Cable, Weld-on Bung, Quick Start Guide.
The PDM 15 is our mid-range PDM, offering all the features of the PDM 10 but adding additional outputs for a total of 15 full configurable and programmable outputs, and 2 canbus networks. The PDM 15 can support a total of 180A of current in the electrical system. Use the canbus networks to trigger outputs in the PDM based on data streaming from the ECU or other canbus devices, then send canbus data from the PDM to your digital dash or datalogger to allow understand the current status of your car's electrical system. The PDM 15 includes the Deutch connectors and pins to get set up and running. Contact us to have your PDM preconfigured before shipping.
AEM 100 PSIg Stainless Sensor Kit. Stainless Steel Sensor Body. 1/8" NPT Male Thread. Includes: 100 PSIg Stainless Sensor, Connector, Pins & 1/8" NPT to -4 Adapter Use to measure fluid pressure up to 100psi. Typical use would be oil or fuel pressure. DO NOT MOUNT DIRECTLY ON ENGINE, always mount remotely via SS line. Vibrations over time will cause sensor fitting to crack.
AEM 150 PSIg Stainless Sensor Kit. Stainless Steel Sensor Body. 1/8" NPT Male Thread. Includes: 150 PSIg Stainless Sensor, Connector, Pins & 1/8" NPT to -4 Adapter Use to measure fluid pressure up to 150psi. Typical use would be oil or fuel pressure. DO NOT MOUNT DIRECTLY ON ENGINE, always mount remotely via SS line. Vibrations over time will cause sensor fitting to crack.