This kit includes the basic parts you'll need to start your S2000 K20/24 swap process. Includes- Hasport K swap Engine Mounts K series engine to F series Transmission Adapter Plate ClutchMaster Steel Flywheel (We can do aluminum for cheaper but STRONGLY recommend steel) OEM Honda Flywheel Bolts (These are older B series flywheel bolts, DO NOT USE S2 Flywheel bolts with the CM flywheel)
Using Honda's well engineered F Series header, we cut off the F series flange and adapt the header to a K Series flange. This is by far our favorite option when K Swapping your S2000. The OEM Header is built extremely well, double wall for best heat management, never cracks, and just fits like an OEM part. Requires a good Core.
Moroso K series Road Race Baffled Steel Oil Pan. This is our pan of choice for heavily tracked S2000 K-swapped cars. Large capacity helps keep the oil temps stable and plenty of oil in the sump at all times. Must have Type S Oil pump conversion.
Adapter plate to mate your K series Engine to the stock S2000 Transmission. Includes the alignment dowels for both sides and hardware to bolt adapter plate to the engine.
Clutch Masters Steel K Swap Flywheel designed to work with the adapter plate and a K series engine to S2 transmission. We strongly recommend the steel flywheel over the aluminum on K24's that are spending a lot of time in the higher RPM's. The long stroke of an inline 4 produce some intense harmonics that can result in transmitting those harmonics into your clutch, or even worse, cause loose/broken flywheel bolts. DO NOT USE your S2000 flywheel bolts. They are too long and will bottom out before properly fastening. We sell the correct bolts.
USDM K series Water Pump Housing. This is what you need to convert your JDM K24 engine to use the USDM Alternator and tensioner setup. The JDM Water Pump and thermostat housing will bolt right up to this. Also includes required OEM shortened stud when converting from a JDM housing to USDM housing.
This is still to date, our preferred method of doing the Kswap into an S2000. This allows you to keep your factory Fuel system (FPR, rail, Injectors), Throttle Body, TPS, MAP, Idle Valve, IAT, and everything fits like factory. The only downside is you do have to do some trimming to fit your intake manifold. [See pics]. Includes: adapter plate, 6 bolts, and NPT 90* coolant fitting.
Figuring out what you need for fittings and lines can be a pain. This kit makes it easy. Includes all the lines and adapter needed to connect directly to the OEM S2 hardline then back to the OEM S2 return line. This kit is designed to feed the OEM K series return-less fuel rail. Can easily be configured for aftermarket fuel rails.
ONLY AVAILABLE WITH PURCHASE OF COMPLETE ASM KSWAP ENGINE PACKAGE OEM Honda K series Valve Cover. 100% stock and unmodified. Highly durable wrinkle black coating. Laser Etched ASM Logo
Skunk2 Alpha series 70mm Throttle body. B series fitment (same for 2000-2005 Honda S2000). Will fit the Kmiata Kswap Intake manifold. Uses B series TPS/MAP sensors. This has been the best budget throttle body we've used. We've seen many of the cheap throttle bodies stick and rattle apart. We've never had that issue with the Skunk2.
Want to use that stock S2000 header? This is our preferred choice when doing a 250hp or less K Swap. Cut off that F series flange, cut the two inner runners, clock them just a touch outwards, and weld that all back together. Do it all correctly and you have perfect OEM fitment.
RWD K Series Rear Coolant Housing - K24/20z3 RBB style. Also included is a 1-1/4" to 1-1/4" Inch Hose Barb Splice Coupler to extend your upper radiator hose. [You'll need to source a short hose with a 90* bend.]
Running a K series engine harness but using your stock S2000 (00-05) throttle body? You will need to convert the TPS Connector to the older B series style. Or just use this quick and easy jumper/adapter. plug in and go.
Putting your engine through 15+ minute track sessions? We strongly recommend adding an engine oil cooler. We've put together this kit from Setrab, and includes everything you need to help keep that engine running strong lap after lap. Includes- Setrab Billet Sandwich Plate w/Thermostat Setrab Series 6 Oil Cooler, 19Row. Setrab Series 6 Oil Cooler Mounting bracket kit. Setrab M22 to 10an Fittings (X4) Stainless Steel 10an Line, 2 4ft pieces.
Requires a good core manifold to be sent in. Ready to ship S2000 intake manifold cut & modified to work with a K-series motor. This will also require an intake manifold adapter plate; sold separately. No sensors, fittings, or hoses included.